15 Search Results

Thin‐film photovoltaic device efficiencies are limited by carrier recombination, thus understanding recombination mechanisms is critical for performance improvements. Bulk minority carrier lifetime ( τ _bulk ) is a critical parameter for solar cells but is difficult to determine in P–N junction devices, especially for high doping. As doping ≥10 ¹⁶  cm ⁻³ is required for efficient drift‐charge‐carrier‐collection devices, a method for τ _bulk determination in doped P–N junction devices is necessary. This work utilizes time‐resolved photoluminescence (TRPL) simulations to quantify bulk and interface recombination properties in highly doped, graded absorber CdSeTe structures. The two methods developed here for τ _bulkmore » determination include utilization of an instantaneous lifetime representation to guide TRPL fitting and direct comparison between measured and simulated decays. Simulations verified that both methods are valid for state‐of‐the‐art device architectures which include graded bandgap absorbers, graded doping, and graded lifetimes. Shifts in the dominant recombination mechanism are identified for sufficiently long τ _bulk , where front and back interface quality plays a more prominent role. Evaluation of surface recombination velocities and conduction band offset illustrate electro‐optical advantages of a positive conduction band offset and highlight the necessity of improved interfaces as bulk quality in photovoltaic devices improves.« less

Magnesium zinc oxide (MZO, Mg_xZn_1-xO) is a leading emitter for CdTe-based solar cells due to its transparency and the ability to tune its conduction band offset with the absorber. Devices employing alloyed cadmium selenide telluride (CST, CdSe_yTe_1-y) absorbers achieved high efficiency (>19%) using MZO deposited by reactive sputtering over a broad composition range (3.68–3.92 eV, x: 0.20–0.35). Minimal differences in implied and measured open circuit voltage indicate that the contacts are well passivated and highly selective across the spectrum of MZO employed. Device performance insensitivity to MZO composition, which is not observed in CdTe devices, is attributed to the formationmore » of an oxygenated interface layer. Se volatility creates a group VI deficiency at the interface that drives O migration from the MZO into the absorber. This introduces conductivity in the emitter not present in its as-deposited state, contributing to the exceptional performance observed. It is shown that the quality of device passivation depends on the oxidation state of the as-deposited MZO such that intelligent control and management of the reactive sputtering process is required.« less

Atomistic modeling based on Desnity Functional Theory (DFT)- 1/2 method coupled with surface Green’s function has been employed to investigate the energy band alignment results in cadmium selenium telluride (CdSeTe) surfaces. The structural and electronic properties of the bulk ternary alloy were established before cleaving the CdSeTe low index surface facets. The dependency of atomic-scale electronic features on different plane orientations was explored by studying the energy band alignment diagrams in the unreconstructed and reconstructed surfaces. While the low index CdSeTe surface geometry reconstructions replicate the CdTe surface geometries, the energy band alignment features of the unreconstructed and reconstructed CdSeTemore » surfaces differ from those observed in CdTe low index surfaces. The structurally relaxed reconstructed CdSeTe surface results in purely flat bands as opposed to an internal cusp feature observed in CdTe surfaces. The presence of an internal energy cusp in CdTe(111) surfaces is expected to play a key role in enhancing the hole charge transport towards the back of CdTe-only solar cell device and the absence of such feature in CdSeTe surface may explain one of the reason for the lower performance of CdSeTe-only solar cell seen experimentally.« less

Magnesium zinc oxide (MZO) is a promising front contact material for CdTe solar cells. Due to its higher band gap than traditional CdS, MZO can reduce parasitic absorption to significantly increase short-circuit current density while also providing a benefit of conduction band offset tuning through Mg:Zn ratio optimization. MZO has been successfully implemented into CdTe devices, however its stability has been of concern. The MZO stability issue has been attributed to the presence of oxygen in the CdTe device processing ambient, leading to double-diode behavior (S-kink) in the current density-voltage curves. Here we report on MZO thin films deposited bymore » reactive co-sputtering. The reactively co-sputtered MZO thin films have encouraging stability, show no significant variation in work function of the surface over a period of 6 months, as measured by Kelvin probe. Energy conversion efficiencies of around 16% have been achieved both with and without presence of oxygen in device processing ambients across multiple research facilities. Finally, these efficiencies should be possible to increase further by tuning of the thin film deposition and device processing parameters, especially through optimization of the back contact.« less

An atomic-scale perspective of energy band alignment in CdTe surfaces has not been spatially studied despite the major role surfaces play in forming interfaces within CdTe-based thin film photovoltaic devices. Atomistic modeling based on density functional theory coupled with surface Green’s function is used for calculating energy band alignment of CdTe surfaces. The CdTe(1 0 0) ((1×1) and c(2×2) reconstruction) and CdTe(1 1 1) ((1×1) and (2×2) reconstruction) facets without and with surface relaxation provide insightful band bending characteristics that influence charge carrier transport. Results show that unrelaxed (1×1) CdTe(1 0 0) and CdTe(1 1 1) surfaces bend the valencemore » band downward with surface polarity dictating the surface potential magnitude. The reconstructed CdTe(1 0 0) c(2×2) and CdTe(1 1 1) (2×2) surfaces result in favorable surface electronic features in relation to their unreconstructed variants. In addition, the structurally relaxed CdTe(1 1 1) surfaces develop an internal energy cusp potential that may enhance hole charge transport toward the back of CdTe solar cell devices. In conclusion, energy band alignments calculated within the study lead to a detailed understanding of how CdTe surfaces may affect CdTe-based thin film photovoltaic applications.« less

Thin-film solar modules based on cadmium telluride (CdTe) technology currently produce the world's lowest cost solar electricity. However, the best CdTe modules now contain a cadmium selenium telluride (CST) alloy at the front of the absorber layer. Despite this, research characterizing the behavior of selenium in alloyed CdTe devices is currently very limited. Here we employ advanced secondary ion mass spectrometry measurements to map the three-dimensional distribution of selenium in a graded CST/CdTe device for the first time. We find significant interdiffusion of selenium between the CST and CdTe layers in the cell, primarily out of the CST grain boundariesmore » and up into the CdTe grain boundaries and grain fringes above. This results in significant lateral variations in selenium concentrations across grains and hence also lateral fields, which we estimate using the measured selenium concentrations.« less

Recent advances in design and processing technology have made possible commercialization of polycrystalline (px)-CdTe as a photovoltaic absorber. Grain boundaries (GBs) are the most prominent structural defects in these devices and undergo significant changes during device fabrication. However, the effects of device fabrication processes on these GBs are not entirely understood. Prevailing models of GBs in thin-film photovoltaics consider individual GBs to have homogeneous properties in their area. Here, using an aberration-corrected scanning transmission electron microscope (STEM)-based low-loss and core-loss electron energy-loss spectroscopy (EELS), we show that back-surface etching of CdTe leads to inhomogeneity within individual grain boundaries. We observemore » that etching the back surface leads to the conversion of a region of GBs from CdTe to an elemental Te, which has an only 0.33 eV band gap, as deep as 1 μm from the back surface. The presence of elemental Te in GBs this deep into the absorber layer will increase recombination in the absorber layer and limit the extractable open-circuit voltage, thus reducing device efficiency. However, additive methods for back contact formation such as deposition of Te, ZnTe, or other materials preserve the CdTe stoichiometry of the GBs. Thus, especially for the next generations of CdTe-based cells having longer minority carrier diffusion length and/or thinner absorber layers, additive back contacting methods are superior.« less

Cadmium Sulphide is the conventional n-type buffer layer used in thin film Cadmium Telluride solar cells. It is well known that Cadmium Sulphide causes optical losses and sulphur diffuses into the absorber during high temperature activation. Sputter-deposited Mg-doped ZnO (MZO) has been shown to be an attractive buffer layer for Cadmium Telluride solar cells due to its transparency and tuneable band gap. It is also stable to high temperature processing and avoids diffusion of elements into the cadmium telluride absorber during the cadmium chloride activation treatment. However, degradation is observed in solar cells incorporating MZO buffer layers. Analysis of themore » MZO film surface potential has revealed significant fluctuations in the thin film work function once the layer is exposed to the atmosphere following deposition. These fluctuations are attributed to the high reactivity to water vapour of the MgO contained in the MZO films. This has been analysed using X-ray Photoelectron Spectroscopy to determine corresponding changes in the surface chemistry. The Zinc Oxide component is relatively stable, but the analysis shows that MgO forms a Mg(OH)₂ layer on the MZO surface which forms a secondary barrier at the MZO/CdTe interface and/or at the interface between MZO and the Fluorine-doped SnO₂. This affects the Fill Factor and as a consequence it degrades the conversion efficiency.« less

Electricity produced by cadmium telluride (CdTe) photovoltaic modules is the lowest-cost electricity in the solar industry, and now undercuts fossil fuel-based sources in many regions of the world. This is due to recent efficiency gains brought about by alloying selenium into the CdTe absorber, which has taken cell efficiency from 19.5% to its current record of 22.1%. Although the addition of selenium is known to reduce the bandgap of the absorber material, and hence increase the cell short-circuit current, this effect alone does not explain the performance improvement. Here, by means of cathodoluminescence and secondary ion mass spectrometry, we showmore » that selenium enables higher luminescence efficiency and longer diffusion lengths in the alloyed material, indicating that selenium passivates critical defects in the bulk of the absorber layer. Here, this passivation effect explains the record-breaking performance of selenium-alloyed CdTe devices, and provides a route for further efficiency improvement that can result in even lower costs for solar-generated electricity.« less